AS 2439.2-2007

1-AS 2439.2-2007 PERFORATED PLASTICS DRAINAGE AND EFFLUENT PIPE AND FITTINGS - PERFORATED EFFLUENT PIPE AND ASSOCIATED...
4-PREFACE
5-CONTENTS
6-SECTION 1 SCOPE AND GENERAL
6-1.1 SCOPE
6-1.2 APPLICATION
6-1.3 REFERENCED DOCUMENTS
6-1.4 DEFINITIONS
6-1.5 TYPES
6-1.6 CLASSIFICATION
7-SECTION 2 GENERAL REQUIREMENTS
7-2.1 SCOPE OF SECTION
7-2.2 MATERIALS
7-2.3 FREEDOM FROM DEFECTS
7-2.3.1 General
7-2.3.2 Spigot ends
7-2.4 DIMENSIONS
7-2.4.1 Diameter
8-2.4.2 Length
9-SECTION 3 PERFORATIONS
9-3.1 TYPE 3 PIPE
9-3.2 TYPE 4 PIPE
10-3.3 FITTINGS
11-SECTION 4 STORAGE AND TRANSPORT
12-SECTION 5 PERFORMANCE REQUIREMENTS
12-5.1 CONDITIONING OF TEST SPECIMENS
12-5.2 BENDING (Type 3 pipe only)
12-5.3 STRAIGHTENING (Type 3 pipe only)
12-5.4 HIGH TEMPERATURE IMPACT RESISTANCE
12-5.5 LOW TEMPERATURE IMPACT RESISTANCE
12-5.6 ELONGATION (Type 3 pipe only)
12-5.7 PIPE STIFFNESS
12-5.8 PERFORATION DEFORMATION
12-5.8.1 Type 3 pipe
13-5.8.2 Type 4 pipe
13-5.9 JOINT SEPARATION (Type 3 pipe only)
13-5.10 MARKING
13-5.10.1 Type 3 pipe
13-5.10.2 Type 4 pipe
14-APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
14-A1 SCOPE
14-A2 RELEVANCE
14-A3 DEFINITIONS
14-A3.1 Acceptable quality level (AQL)
14-A3.2 Batch
14-A3.3 Batch release test
14-A3.4 Inspection level
14-A3.5 Lot
14-A3.6 New formulation
15-A3.7 Process verification test (PVT)
15-A3.8 Sample
15-A3.9 Sampling plan
15-A3.10 Type test (TT)
15-A4 PRODUCT CERTIFICATION
15-A5 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
15-A5.1 General
15-A5.2 Retesting
16-A5.3 Rejection after test
16-A6 NEW FORMULATION
18-APPENDIX B - MEASUREMENT OF DIMENSIONS
18-B1 SCOPE
18-B2 APPARATUS.
18-B3 PREPARATION OF TEST SPECIMENS
18-B3.1 Diameter-Outside and inside
18-B3.2 Length
18-B3.3 Perforations
18-B4 TEST PROCEDURES
19-B5 REPORT
19-B5.1 Outside diameter
19-B5.2 Inside diameter
19-B5.3 Length
19-B5.4 Perforations
20-APPENDIX C - BENDING TEST (TYPE 3 ONLY)
20-C1 SCOPE
20-C2 PRINCIPLE
20-C3 APPARATUS
20-C4 PREPARATION OF TEST SPECIMENS
20-C5 TEST PROCEDURE
20-C6 REPORT
21-APPENDIX D - STRAIGHTENING TEST AT 0°C (TYPE 3 ONLY)
21-D1 SCOPE
21-D2 PRINCIPLE
21-D3 APPARATUS
21-D4 PREPARATION OF TEST SPECIMENS
21-D5 TEST PROCEDURE
21-D6 REPORT
22-APPENDIX E - HIGH TEMPERATURE IMPACT RESISTANCE
22-E1 SCOPE
22-E2 PRINCIPLE
22-E3 APPARATUS
22-E4 PREPARATION OF TEST SPECIMENS
22-E5 TEST PROCEDURE
22-E6 REPORT
23-APPENDIX F - LOW TEMPERATURE IMPACT RESISTANCE
23-F1 SCOPE
23-F2 PRINCIPLE
23-F3 APPARATUS
23-F4 PREPARATION OF TEST SPECIMENS
23-F5 TEST PROCEDURE
23-F6 REPORT
24-APPENDIX G - ELONGATION AND PERFORATION DEFORMATION (TYPE 3 ONLY)
24-G1 SCOPE
24-G2 PRINCIPLE
24-G3 APPARATUS
24-G4 PREPARATION OF TEST SPECIMENS
24-G5 TEST PROCEDURE
24-G6 CALCULATION
25-G7 REPORT
25-G7.1 Pipe elongation
25-G7.2 Perforation deformation
26-APPENDIX H - PERFORATION DEFORMATION
26-H1 SCOPE
26-H2 PRINCIPLE
26-H3 APPARATUS
26-H4 PREPARATION OF TEST SPECIMENS
26-H5 TEST PROCEDURE
26-H6 CALCULATIONS
27-H7 REPORT
27-H7.1 Pipe stiffness
27-H7.2 Perforation deformation (Type 4 only)
28-APPENDIX I - JOINT SEPARATION (TYPE 3 ONLY)
28-I1 SCOPE
28-I2 PRINCIPLE
28-I3 APPARATUS
28-I4 PREPARATION OF TEST SPECIMEN
28-I5 TEST PROCEDURE
28-I6 REPORT